Back to Water glossary

Water glossary

Wet Scrubber Systems for Flue Gas Desulfurization (FGD)

Explore the mechanics of wet scrubber systems for flue gas desulfurization, including chemical processes, blowdown management, and wastewater treatment protocols.

Wet scrubber systems are a critical technology for Flue Gas Desulfurization (FGD), designed to remove sulfur dioxide (SO₂) from industrial exhaust gases. These systems are essential for environmental compliance and air quality control, particularly in industries like power generation and large-scale manufacturing.

The Wet Scrubber Process

In limestone or lime wet FGD, an alkaline slurry containing limestone (CaCO₃) or lime (Ca(OH)₂) contacts the flue gas. These solids should not be described as entirely dissolved sorbent solutions.

Chemical Reactions and Countercurrent Flow

In a common configuration, the alkaline sorbent slurry is sprayed into a spray tower. A countercurrent flow system is employed, where the sorbent slurry is introduced from the top, flowing downwards, while the hot flue gas enters from the bottom, moving upwards. This design maximizes contact between the gas and the liquid sorbent.

The alkaline slurry neutralizes SO₂. Simplified overall reactions are shown below; actual aqueous species and sulfite hydrates depend on the process conditions:

  1. Sulfur Dioxide Absorption: SO₂(g) + CaCO₃(s) → CaSO₃(s) + CO₂(g)
    • or SO₂(g) + Ca(OH)₂(s) → CaSO₃(s) + H₂O(l)

In forced-oxidation systems, air oxidizes calcium sulfite (CaSO₃) and calcium sulfate dihydrate (CaSO₄·2H₂O), or gypsum, forms. An overall balanced representation is:

  1. Oxidation to Gypsum: 2CaSO₃(s) + O₂(g) + 4H₂O(l) → 2CaSO₄·2H₂O(s) (Gypsum)

Limestone Forced Oxidation (LSFO)

Limestone Forced Oxidation (LSFO) promotes sulfite oxidation and controlled gypsum production. It can help manage scaling, but still requires suitable oxidation, solids control and slurry operating conditions; it is not a guarantee against deposition.

FGD Blowdown Management and Wastewater Treatment

Effective management of the circulating slurry is crucial due to the accumulation of impurities.

Necessity of Blowdown

Over time, the circulating slurry accumulates high concentrations of Total Dissolved Solids (TDS), Total Suspended Solids (TSS), heavy metals, and chlorides. To prevent these impurities from impairing scrubber efficiency and material integrity, a portion of the circulating slurry must be continuously purged. This purge stream is known as the FGD blowdown effluent.

System Types: Regenerable vs. Once-Through

FGD systems can be classified by what happens to the sorbent after sulfur capture, rather than by whether slurry circulates within the absorber:

  • Regenerable Systems: The sorbent is regenerated, releasing captured sulfur into a separate recovery stream, and returned to sulfur capture. Adding fresh lime to circulating slurry alone is not sorbent regeneration.
  • Once-Through Systems: The sorbent is consumed, producing waste or a byproduct such as gypsum. Slurry can still circulate internally, and a controlled purge goes to wastewater treatment; the term does not mean all absorber slurry is discharged after one pass.

Once-Through Wastewater Treatment Steps

For once-through systems, the FGD blowdown undergoes a multi-stage treatment process:

  1. Equalization Tank: The effluent from the SO₂ absorber first enters an equalization tank. This stage helps to homogenize contaminant concentrations and flow rates, providing a more consistent influent for subsequent treatment steps.
  2. Desaturation: Where required, condition pH and precipitate scale-forming constituents, then separate solids to reduce downstream supersaturation. Select reagents from the actual wastewater chemistry rather than treating this step as removal of residual gaseous SO₂.
  3. Reaction Tanks: The wastewater then moves to reaction tanks where specific chemicals are added to promote:
    • Further Oxidation: Converting residual sulfite where required, with endpoint verification.
    • Precipitation: Removing selected metals and scale-forming species. Precipitation does not remove all dissolved salts, including chloride.
    • Agglomeration: Ferric chloride may be used for coagulation and coprecipitation, while a suitable polymer assists flocculation. Confirm reagents, dose and mixing through actual-water tests.
  4. Clarifier: The treated water flows into a clarifier, where the agglomerated solids (sludge) settle by gravity. The clarifier effectively separates the solids from the liquid effluent.
  5. Sludge Management: Clarifier sludge is collected and dewatered, commonly by filter press or centrifuge. Characterize contamination and the applicable disposal or reuse requirements. Wastewater-treatment sludge containing captured metals is not automatically equivalent to separately recovered saleable FGD gypsum.
  6. Overflow Treatment: Select further treatment for the actual discharge or reuse targets. Clarification and pH adjustment may leave dissolved salts, selenium or nitrogen compounds requiring specific treatment; generic filtration or oxidation cannot be assumed to meet every limit.

AquaChain Engineering Tip

To optimize sorbent utilization and minimize scaling in wet scrubbers, implement real-time monitoring of both SO₂ inlet concentrations and absorber slurry pH. This data allows for precise, dynamic adjustment of sorbent feed rates, enhancing removal efficiency while preventing over-dosing that can lead to increased chemical costs and secondary scaling or fouling issues.

Frequently Asked Questions

What is the primary purpose of a wet scrubber in FGD?

The primary purpose is to remove sulfur dioxide (SO₂) from industrial flue gases, preventing its release into the atmosphere and mitigating acid rain and other environmental impacts.

Why is "blowdown" necessary in wet scrubber systems?

Blowdown is necessary to remove accumulated impurities such as Total Dissolved Solids (TDS), Total Suspended Solids (TSS), heavy metals, and chlorides from the circulating sorbent slurry. Without blowdown, these impurities would reduce scrubber efficiency and potentially damage equipment.

What is gypsum, and how is it produced in a wet scrubber?

Gypsum is calcium sulfate dihydrate (CaSO₄·2H₂O). In a wet scrubber, it is produced by injecting air into the calcium sulfite (CaSO₃) slurry, which oxidizes the sulfite into sulfate, forming gypsum as a solid by-product.

References