Back to Water glossary

Water glossary

Surface Water Discharge of Brine

A technical guide on the methods, environmental considerations, and cost factors for discharging brine into surface water bodies, particularly from desalination plants.

Introduction to Surface Water Brine Discharge

Surface water discharge is a common brine-management route for seawater reverse osmosis (SWRO), where site assessment and permits allow release into receiving waters. A historical Lenntech account states over 90% of large SWRO plants and lists Hadera, Israel at 462,000 m³/day (122 million GPD), Tuas SW, Singapore at 136,000 m³/day (36 million GPD), and Larnaca, Cyprus at 64,000 m³/day (17 million GPD). These are historical supplier examples, not a current global inventory or proof of present capacities or approvals.

Methods of Brine Discharge

The most common methods for brine discharge into surface water bodies include:

  • Direct surface discharge: Releasing brine directly into the nearshore or offshore marine environment.
  • Discharge into a wastewater treatment plant: Co-disposal with treated effluent may improve mixing, but requires utility acceptance, hydraulic and biological compatibility and discharge approval; dilution does not remove salt mass.

Design for Brine Dispersion and Mixing

Brine outfalls are engineered to minimize the area where salinity exceeds the tolerance limits of the aquatic ecosystem. This is achieved by rapidly mixing the brine with the receiving water body. Key factors in enhancing mixing include:

  1. Local Tidal (Surf) Zone Mixing Capacity: Utilizing the natural turbulence and currents of the nearshore environment.
  2. Offshore Discharge with Diffusers: Extending the outfall beyond the immediate tidal zone and installing diffusers at the pipe's end to promote efficient mixing and dilution.

Nearshore tidal zones often have limited capacity to transport and dissipate high salinity loads. If the salt load surpasses this capacity, excess salts can accumulate, leading to long-term salinity increases that may exceed the aquatic ecosystem's tolerance. Hydrodynamic modeling is essential to determine the salinity mixing/transport capacity of these zones.

For smaller plants, ≤1,000 m³/day or 0.26 million GPD is a historical sizing example, not a rule permitting an open-ended pipe several hundred meters offshore. Larger SWRO outfalls may use diffusers, but they do not guarantee that dense brine cannot contact the seabed. Verify near- and far-field mixing, bathymetry, tides, currents and permit criteria for the actual site.

Potential Environmental Impacts

Selecting an appropriate location for a brine discharge system requires careful consideration of several factors:

  • Ecological Sensitivity: Avoiding areas with endangered species or stressed aquatic ecosystems.
  • Hydrodynamic Conditions: Identifying locations with strong underwater currents for rapid and effective dissipation of the high-salinity discharge.
  • Navigational Safety: Steering clear of maritime traffic routes to prevent damage to the outfall system and alterations to mixing patterns.
  • Construction Feasibility: Compare depth, distance, seabed and installation costs together with required dilution and habitat protection; shallow nearshore water is not universally the preferred discharge location.

The primary environmental concerns associated with surface water brine disposal include:

  • Salinity Tolerance: Exceeding the salinity tolerance of the local aquatic ecosystem.
  • Concentration of Constituents: Increasing the concentration of specific water constituents to harmful levels.
  • Discoloration and Low Oxygen: Visual impact from discolored plumes or oxygen depletion in the receiving waters.

Assessing the feasibility of surface water brine discharge involves addressing key questions:

  • Plume Dispersion and Recirculation: Evaluating the movement and potential return of the discharged plume.
  • Discharge Toxicity: Assessing the inherent toxicity of the brine components.
  • Regulatory Compliance: Ensuring the discharged water quality meets relevant regulatory standards.
  • Ecosystem Salinity Capacity: Determining the local aquatic ecosystem's capacity to assimilate salinity to design the discharge point for minimal impact.

Potential Brine Treatment Requirements for SWRO

Deep-sea intake does not itself establish that SWRO brine can be discharged untreated. Similar major-ion composition does not eliminate elevated salinity, residual oxidants, chemicals, metals or low-oxygen impacts. Diffusers or blending require a site-specific permit and monitoring; <40,000 mg/L or 4% is a historical example, not a universal safe threshold, and mass-per-volume concentration is not automatically a mass-percent salinity.

However, if feed water is sourced from beach wells or coastal alluvial aquifers, the desalination concentrate may require treatment due to:

  • Iron (Fe) and Manganese (Mn) Concentration: Reduced groundwater can contain dissolved Fe and Mn, which may concentrate during RO. Aeration can oxidize dissolved ferrous ions and generate colored iron hydroxide or oxyhydroxide particles, including FeO(OH); FeS is a sulfide solid, not the general dissolved ferrous species. Assess feed oxidation and separation, or actual brine oxidation and solids removal, according to the chemistry and discharge requirement.
  • Low Dissolved Oxygen (DO): Significant discharge of brine with low DO can lead to oxygen depletion and stress for the local aquatic ecosystem. In such instances, brine reaeration is necessary.

Surface Water Discharge Cost Considerations

Construction costs for surface water brine discharge facilities are highly dependent on site-specific factors:

  • Brine Discharge Flow Rate: Higher flows necessitate larger infrastructure.
  • Nearshore vs. Offshore Discharge: Offshore discharges typically require longer pipelines and more complex installation.
  • Construction Materials: Type and grade of materials used for pipelines and diffusers.
  • Diffuser System Complexity: The design and number of diffusers.
  • Brine Transport Costs: Cost of conveying brine from the desalination plant to the discharge point.
  • Brine Treatment Costs: If pre-discharge treatment is required.
  • Environmental Monitoring: Costs associated with ongoing environmental assessment of the discharge.

Pipeline installation depends on ground, seabed, waves, anchors and navigation. A historical comparison gives submarine trenching as 3 to 5 times onshore trenching and concrete supports every 5 to 10 m (16 to 33 ft); these are examples, not universal cost multipliers or structural spacing. Choose burial or seabed placement from actual engineering and environmental requirements.

Concentrate transport costs are proportional to the brine flow rate and the distance between the desalination plant and the discharge outfall. The outfall's construction costs, size, and diffuser system configuration (influenced by brine volume, salinity, and hydrodynamic conditions) are all site-specific variables.

Environmental monitoring costs can be substantial, particularly when discharging into ecologically sensitive areas.

AquaChain Engineering Tip

When designing a brine outfall, prioritize detailed 3D hydrodynamic modeling of the receiving water body. This enables optimization of diffuser design, location, and orientation to maximize initial dilution and predict far-field dispersion, preventing unwanted brine accumulation and ensuring ecological protection.

Frequently Asked Questions

Q1: What is the primary environmental concern with surface water brine discharge?

A1: The main concern is increasing the salinity of the receiving water body beyond the tolerance levels of the local aquatic ecosystem, potentially harming marine life and habitats.

Q2: Why is brine from deep-sea intakes often discharged without prior treatment?

A2: Similar major-ion composition can reduce some compositional differences, but does not establish safe untreated discharge. Evaluate salinity, chemicals, metals, dissolved oxygen, plume behavior and the site permit before deciding whether treatment is needed.

Q3: What makes offshore brine outfall construction costly?

A3: Offshore outfalls involve longer pipelines, more complex installation techniques (often laying pipes on the ocean floor secured with concrete blocks rather than trenching), and require specialized marine equipment, all contributing to higher construction costs.

Related Resources

References