Ultrapure Water (UPW) in Semiconductor Manufacturing
The production of plasma displays, advanced chips, and integrated circuits demands water of exceptionally high quality for various critical process steps. This water, known as Ultrapure Water (UPW), is crucial to prevent contamination that could compromise device performance and yield. As semiconductor linewidths continue to shrink, the purity requirements for UPW become even more stringent, pushing the boundaries of water treatment technology.
UPW Production System Overview
Achieving the required UPW standards involves an integrated approach combining multiple advanced water treatment technologies. A typical UPW production system is engineered for maximum contaminant removal, including dissolved solids, organics, particulates, dissolved gases, and microorganisms.
Key technologies commonly employed include:
- Reverse Osmosis (RO): For primary removal of dissolved salts and large organic molecules.
- Electro-Deionization (EDI): Continuous deionization for further reduction of ionic impurities without chemical regenerants.
- Ion Exchange (IX): Mixed-bed ion exchangers for polishing to achieve ultra-low conductivity.
- Ultraviolet (UV) Treatment: UV oxidation can reduce TOC under the appropriate wavelength and process conditions, while UV disinfection controls microorganisms. These are different duties; ordinary disinfection alone does not guarantee TOC removal, and oxidation products may require downstream polishing.
- Ultrafiltration (UF) / Microfiltration (MF): For particulate removal.
A well-designed UPW system requires a strategic selection of technologies and equipment, tailored to the specific feed water quality and the end-user's ultrapure water requirements. Various configurations can be applied to meet different demands.
ASTM UPW Quality Guidelines for Semiconductor Industry
ASTM D5127 provides guidance for electronics and semiconductor water quality at the point of distribution (POD). The Type E.1, E 1.1 and E 1.2 classifications below illustrate older linewidth-based categories; later guidance includes additional categories. A fab must specify the applicable edition, process requirements and point-of-use (POU) quality rather than infer acceptance from linewidth alone.
The following legacy comparison illustrates the parameters associated with three older categories. It is not a reproduction of every requirement in the applicable ASTM edition or a current universal acceptance specification. Resistivity values are minima; most impurity values are maxima, and analytical method, sampling volume and particle-size definition matter.
| Parameter | Unit | Type E.1 | Type E 1.1 | Type E 1.2 |
|---|---|---|---|---|
| Linewidth | µm | 1.0-0.5 | 0.35-0.25 | 0.18-0.09 |
| Resistivity, 25 °C | MΩ·cm | ≥18.1 | ≥18.2 | ≥18.2 |
| TOC (on-line) | µg/L (ppb) | ≤5 | ≤2 | ≤1 |
| On-line dissolved oxygen | µg/L (ppb) | ≤25 | ≤10 | ≤3 |
| On-Line Residue after evaporation | µg/L (ppb) | ≤1 | ≤0.5 | ≤0.1 |
| SEM particles | ||||
| > 0.1-0.2 µm (0.004-0.008 mils) | Particles/mL | ≤1,000 | ≤700 | ≤250 |
| > 0.2-0.5 µm (0.008-0.02 mils) | Particles/mL | ≤500 | ≤400 | ≤100 |
| > 0.5-1.0 µm (0.02-0.04 mils) | Particles/mL | ≤100 | ≤50 | ≤30 |
| > 10 µm (0.4 mils) | Particles/mL | ≤50 | ≤30 | ≤10 |
| Bacteria in CFU/Volume | ||||
| 100 mL Sample | CFU/100mL | ≤5 | ≤3 | ≤1 |
| 1 L Sample | CFU/L | ≤10 | ≤10 | Not specified |
| 10 L Sample | CFU/10L | Not specified | Not specified | Not specified |
| Silica | ||||
| Total | µg/L (ppb) | ≤5 | ≤3 | ≤1 |
| Dissolved | µg/L (ppb) | ≤3 | ≤1 | ≤0.5 |
| Anions and Ammonium by IC | µg/L (ppb) | |||
| Ammonium | ≤0.1 | ≤0.1 | ≤0.05 | |
| Bromide | ≤0.1 | ≤0.05 | ≤0.02 | |
| Chloride | ≤0.1 | ≤0.05 | ≤0.02 | |
| Fluoride | ≤0.1 | ≤0.05 | ≤0.03 | |
| Nitrate | ≤0.1 | ≤0.05 | ≤0.02 | |
| Nitrite | ≤0.1 | ≤0.05 | ≤0.02 | |
| Phosphate | ≤0.1 | ≤0.05 | ≤0.02 | |
| Sulfate | ≤0.1 | ≤0.05 | ≤0.02 | |
| Metals by ICP/MS | µg/L (ppb) | |||
| Aluminum (Al) | ≤0.05 | ≤0.02 | ≤0.005 | |
| Antimony (Sb) | Not specified | Not specified | Not specified | |
| Arsenic (As) | Not specified | Not specified | Not specified | |
| Barium (Ba) | ≤0.05 | ≤0.02 | ≤0.01 | |
| Boron (B) | ≤0.3 | ≤0.1 | ≤0.05 | |
| Cadmium (Cd) | Not specified | Not specified | Not specified | |
| Calcium (Ca) | ≤0.05 | ≤0.02 | ≤0.002 | |
| Chromium (Cr) | ≤0.05 | ≤0.02 | ≤0.002 | |
| Copper (Cu) | ≤0.05 | ≤0.02 | ≤0.002 | |
| Iron (Fe) | ≤0.05 | ≤0.02 | ≤0.002 | |
| Lead (Pb) | ≤0.05 | ≤0.02 | ≤0.005 | |
| Lithium (Li) | ≤0.05 | ≤0.02 | ≤0.003 | |
| Magnesium (Mg) | ≤0.05 | ≤0.02 | ≤0.002 | |
| Manganese (Mn) | ≤0.05 | ≤0.02 | ≤0.002 | |
| Nickel (Ni) | ≤0.05 | ≤0.02 | ≤0.002 | |
| Potassium (K) | ≤0.05 | ≤0.02 | ≤0.005 | |
| Sodium (Na) | ≤0.05 | ≤0.02 | ≤0.005 | |
| Strontium (Sr) | ≤0.05 | ≤0.02 | ≤0.001 | |
| Tin (Sn) | Not specified | Not specified | Not specified | |
| Titanium (Ti) | Not specified | Not specified | Not specified | |
| Vanadium (V) | Not specified | Not specified | Not specified | |
| Zinc (Zn) | ≤0.05 | ≤0.02 | ≤0.002 |
Note: ASTM D5127-13(2018) describes seven classifications down to 0.032 µm, so E-1.1 and E-1.2 are not its only highest-purity categories. Use the selected standard and fab specification for design and acceptance. “Not specified” here does not mean that the substance is harmless or need not be assessed.
AquaChain Engineering Tip
For critical semiconductor UPW systems, consider deploying advanced real-time particle counters at various stages, especially at point-of-use. While resistivity and TOC are fundamental, sub-micron particle excursions can be fleeting and severely impact yield. Online particle monitoring provides immediate actionable data, allowing for rapid intervention before widespread wafer contamination occurs.
Frequently Asked Questions
Q: Why is ultrapure water quality so crucial for semiconductor manufacturing?
A: Minute impurities, even at parts-per-trillion levels, can cause defects in integrated circuits, leading to device failures and reduced manufacturing yields. UPW ensures a clean environment for sensitive processes like etching, cleaning, and deposition.
Q: What are the primary stages in a typical semiconductor UPW system?
A: A typical system includes pre-treatment (filtration, softening, carbon), primary purification (Reverse Osmosis), intermediate polishing (EDI, degasification, UV), and final polishing (mixed-bed ion exchange, ultrafiltration, and point-of-use filtration).
Q: How often should UPW quality be monitored in a semiconductor facility?
A: Critical parameters like resistivity, TOC, and dissolved oxygen are typically monitored continuously (on-line). Other parameters like specific ions, particles, and bacteria are monitored at frequent intervals (e.g., daily, weekly) depending on the criticality and system stability.
For more detailed information on water quality requirements, explore our article on Ultrapure Water.