FulFlo TruBind Standard Filter Cartridge

Summary

Product identification

Parker Fulflo® TruBind absorbent cartridges utilize a modified polymeric absorbent to economically and effectively reduce trace hydrocarbon contamination in aqueous fluids. The enhanced polymer is configured in a radial-flow-design cartridge for maximum utilization of available surface area.

• Cartridge Series: TBC (TruBind Absorbent Cartridge)
• Materials of Construction:
  • Absorbent: Proprietary modified polymer
  • Support Construction: 100% polyolefin
  • Seal Material: Gasket (Polyethylene Foam); 222 O-Ring (Buna-N)
• Key Features:
  • Absorbs and binds hydrocarbon molecules into its interior matrices.
  • Absorbed hydrocarbon is chemically bound by polymer and is not leachable.
  • Radial flow design allows maximum flow with minimal pressure drop.
  • High integrity construction withstands harsh process environments.
  • Completely incinerable.

Operating limits

• Maximum Recommended Operating Temperature:
  • 150°F (65°C) @ 20 psid (1.4 bar)
  • 180°F (82°C) @ 10 psid (0.7 bar)
• Maximum Recommended Operating Pressure: 60 psid (4.1 bar) @ 75°F (24°C)
• Recommended Flow Rate: 1.0 gpm per 10-inch cartridge
• Changeout Pressure Drop (net): 10 psi (0.7 bar)

Feed water

TruBind cartridges are designed to reduce trace hydrocarbon contamination in aqueous fluids, including free, emulsified, and dissolved oils, synthetic lubricants, grease, and a multitude of organic solvents.

Product water

The cartridges typically reduce trace hydrocarbon contaminant in excess of 95% in single-pass mode at a flow rate of 1.0 gpm per 10-inch cartridge. Effluent hydrocarbon levels in water have been shown to be below current and proposed EPA limits as indicated by accelerated testing (Toxic Characteristics Leachate Procedure - TCLP). Series or multipass filtration can virtually eliminate hydrocarbon contamination.

Mechanical / hydraulic

• Cartridge Dimensions (nominal):
  • Lengths: 10-40 in (249mm-1016mm)
  • Outside Diameter: 2-1/2 in (63.5 mm)
  • Inside Diameter: 1-1/16 in (27 mm)
• Flow Factor: 0.03 psid per 1 gpm at 1 cks viscosity per 10 in cartridge

Applications

• Water Soluble Machine Tool Coolants
• Alkaline Parts Washing
• Industrial Discharge Water
• Produced Water Disposal
• Injection Molding Cooling Water
• E-Coat Paint
• Pre R.O. Membrane
• Tanker Ballast Water
• Aerosol Mists
• Plating Bath
• Leisure/Commercial Shipping Bilge Water
• Surface Water Runoff (Truck stops, airports, auto service stations)
• Gas & Oil Facility Wastewater
• Car & Truck Wash Water
• Compressor Condensate
• Post Oil/Water Separator Polishing
• Floor Scrubbing Waste Water
• Pre Carbon Bed

Performance Data

• Hydrocarbon Removal Efficiency: >95% reduction in trace hydrocarbon contaminant in single-pass mode at 1.0 gpm per 10-inch cartridge, maintained up to a net differential pressure of 10 psi.
• Hydrocarbon Absorbent Capacity: Up to 250 grams (approximately one-half pint) of low density hydrocarbon contaminant. Capacity decreases with increasing hydrocarbon density.
• Expected Life Data (per 10-inch cartridge at 1.0 gpm flow rate):

BioSafety

The TruBind cartridge is classified as non-hazardous and incinerable. Disposal must adhere to local regulations pertaining to the absorbed contaminant.

---

Disclaimer: This summary is based on the provided text extraction and may not include all figures, footnotes, or the latest revisions from the original OEM PDF datasheet. Contractual data should always match the specific OEM PDF revision used for the project.

Official datasheet (PDF)

Lenntech datasheet mirror