FulFlo TruBind 300 Filter Cartridge

Summary

Product identification

The Fulflo® TruBind™ 300 Cartridges are designed for effective and economical hydrocarbon removal from aqueous fluids. These enhanced polymeric absorbent cartridges utilize a modified polymer that both absorbs and chemically binds hydrocarbon molecules into its interior matrices. The radial-flow design maximizes surface area utilization and allows maximum flow with minimal pressure drop.

Applications

• Water Soluble Machine
• Alkaline Parts Washing
• Industrial Discharge Water
• Produced Water Disposal
• E-Coat Paint
• Post Oil/Water Separator
• Compressor Condensate
• Car & Truck Wash Water
• Plating Bath
• Gas & Oil Facility Wastewater
• Surface Water Runoff (Truck stops, airports, auto service stations)
• Bilge Water
• Pre Carbon Bed
• Aerosol Mists Cooling Water
• Tanker Ballast Water
• Pre R.O. Membrane Polishing

Operating limits

• Maximum Recommended Operating Conditions:
  • Temperature: 150°F (65°C) @ 20 psid (1.4 bar); 180°F (82°C) @ 10 psid (0.7 bar)
  • Pressure: 40 psid (2.8 bar) @ 75°F (24°C)
  • Changeout Pressure Drop (net): 10 psi (0.7 bar)
  • pH Range: 2 - 12
• BioSafety: The TruBind cartridge is classified as non-hazardous and incinerable. Disposal must be dictated by local regulations pertaining to the absorbed contaminant.

Mechanical / hydraulic

• Dimensions:
  • Lengths: 10-40 in (249mm-1016mm)
  • Outside Diameter: 2-1/2 in (63.5 mm)
  • Inside Diameter: 1-1/16 in (27 mm)
• Flow Rate: 1.0 gpm per 10-inch cartridge (recommended maximum for most effective removal of trace hydrocarbon contaminant).
• Flow Factor: 0.03 psid per 1 gpm at 1cks viscosity per 10 in cartridge
• Recommended Vessels: All standard Fulflo vessels designed for 2-1/2 in OD cartridges.

Materials of Construction

• Absorbent: Proprietary modified polymer
• Support Construction: 100% polyolefin
• Seal Material: Gasket (Polyethylene Foam); 222 O-Ring (Buna-N)

Product water

• Hydrocarbon Removal Efficiency:
  • At an equivalent flow rate of 1.0 gpm per 10-inch cartridge, the TruBind cartridge typically reduces trace hydrocarbon contaminant in excess of 95% in single pass mode.
  • This efficiency level can be maintained only to a net differential pressure of 10 psi.
  • Series or multipass filtration can virtually eliminate hydrocarbon contamination.
• Hydrocarbon Absorbent Capacity:
  • The cartridge medium has the potential to remove up to 250 grams (approximately one-half pint) of low density hydrocarbon contaminant.
  • Absorbent capacity will decrease as density of hydrocarbon increases.
  • See the official PDF for exact tabulated values regarding estimated life data based on hydrocarbon concentration, removal per minute, and estimated gallons treated.

Ordering Information

• Cartridge Series: TBC (TruBind Absorbent Cartridge)
• Support Core: A = Standard Wall Polypropylene Core
• Seal Material:
  • A = Polyolefin Foam Gasket (standard for “DO” seal design)
  • N = Buna-N O-Ring (standard for “TC” seal design)
• End Cap Configuration:
  • DO = Double-Open-End (gasket seal)
  • DX = DOE w/core extender
  • TC = Single-Open-End (222 O-ring seal)
  • TX = 222 O-ring/Flex Fin
• Available Lengths (code, in, mm):
  • 9: 9-5/8 (244)
  • 10: 9-13/16 (249)
  • 19: 19-5/8 (498)
  • 20: 19-15/16 (506)
  • 29: 29-1/4 (743)
  • 30: 30-1/16 (764)
  • 39: 39 (991)
  • 40: 40 (1016)

---

Disclaimer: This summary is based on extracted text and may not include all figures, footnotes, or the latest revisions from the original OEM PDF. Contractual data must match the specific OEM PDF revision used on the project.

Official datasheet (PDF)

Lenntech datasheet mirror