Tóm tắt tài liệu kỹ thuật
Memtrex HFE-T
Engineering summary from PDF text extraction for Memtrex HFE-T. Verify every value with the OEM datasheet.
Summary
Product identification
Memtrex HFE-T filters feature an ePTFE membrane edge-laminated on Halar (ECTFE), with polyester plastic parts. They are pleated filters with PTFE membrane.
Available absolute pore size micron ratings:
- 0.05 µm
- 0.1 µm
- 0.2 µm
- 0.45 µm
- 1 µm
Materials of Construction
- Core and Cage: Polyester
- Support Layer: Halar (ECTFE)
- Membrane: ePTFE
- End Caps: Polyester
Mechanical / hydraulic
Dimensions
The nominal O.D. for all listed filter models is 2.75” (70 mm) and the nominal I.D. is 1.25” (31 mm). See the official PDF for exact tabulated filter models.
Operating limits
- Maximum Forward Differential Pressure: 60 psi (4.14 bar) at 70°F (21.1°C)
- Maximum Reverse Differential Pressure: 30 psi (2.07 bar) at 70°F (21.1°C)
- Maximum Operating Temperature: 205ºF (96.1ºC) at 25 psid (1.7 bar)
Flow performance
Flow performance data in clean water is based on a 10” length filter. See the official PDF for exact tabulated values.
Integrity Testing
- 0.05 µm: ≤ 5 cc / min at 40 psig (2.76 bar)
- 0.1 µm: ≤ 5 cc / min at 40 psig (2.76 bar)
- 0.2 µm: ≤ 5 cc / min at 30 psig (2.07 bar)
- 0.45 µm: ≤ 5 cc / min at 20 psig (1.38 bar)
- 1 µm: ≤ 5 cc / min at 15 psig (1.38 bar)
Certifications and Compliance
- Memtrex HFE-T pleated filters meet U.S. FDA requirements for food contact under applicable regulations in 21 CFR.
- Meet the test criteria for USP Class VI-121°C Plastics.
- Aqueous extracts contain less than 0.25 EU/ml.
- Typically exhibit low levels of non-volatile residues.
Applications
Memtrex HFE-T filters are suitable for very harsh chemical environments. They are manufactured and packaged in a cleanroom environment.
Typical applications include:
- Chemicals
- Microelectronics
- Pharmaceuticals
Additional Information
Filters may be sanitized with compatible chemical agents but must not be autoclaved or steam sterilized. Users should carefully verify chemical compatibility for each application.
Ordering information
- Type: MHFE-T
- Absolute Micron Rating:
- 85 = 0.05 µm
- 91 = 0.1 µm
- 92 = 0.2 µm
- 94 = 0.45 µm
- Nominal Cartridge Length:
- 1 = 10 in (25 cm)
- 2 = 20 in (51 cm)
- 3 = 30 in (76 cm)
- 4 = 40 in (102 cm)
- End #1 Adapter:
- A = Open End Gasket
- E = 222 O-Ring
- F = 226 O-Ring
- End #2 Adapter:
- A = Open End Gasket
- E = Closed End Cap
- H = Fin Adapter
- Elastomer Material: T = Teflon Encapsulated Viton
- Product Grade:
- E = Electronic grade rinse
- Pre Wet = Rinsed and packed wet
Disclaimer: This summary is based on the provided text extract. It may not include all figures, footnotes, or the latest revisions present in the complete OEM PDF. For contractual data, always refer to the specific OEM PDF revision used on the project.
Official datasheet (PDF)
Nội dung tổng hợp từ tài liệu kỹ thuật công khai nhằm tra cứu và so sánh sơ bộ. Bản tóm tắt không thay thế bảng dữ liệu hiện hành được nhà sản xuất chứng nhận. Kiểm tra phiên bản và giới hạn thiết kế trước khi sử dụng.