FulFlo TruBind 400 Filter Cartridge

Summary

Product identification

Fulflo® TruBind™ 400 Cartridges are enhanced polymeric absorbent cartridges designed for effective and economical reduction of trace hydrocarbon contamination in aqueous fluids. The product utilizes a proprietary modified polymer in a radial-flow-design cartridge to absorb and chemically bind hydrocarbon molecules.

Benefits:

• Increases machine tool life when installed at point-of-use.
• Increases working life of valuable process fluids.
• Reduces hydrocarbon levels to meet EPA discharge regulations.
• Absorbed hydrocarbon is chemically bound by polymer and is not leachable.
• Absorbent polymer is enhanced to maximize utilization of surface area.
• Radial flow design of cartridge allows maximum flow with minimal pressure drop.
• High integrity construction withstands harsh process environment.
• TruBind™ cartridges are completely incinerable.
• Parker’s TQM system assures consistent and reliable performance.

Applications:

• Water Soluble Machine Tool Coolants
• Alkaline Parts Washing
• Industrial Discharge
• Car & Truck Wash Water
• Gas & Oil Facility Wastewater
• Tanker Ballast Water
• Bilge Water
• Surface Water Runoff
• Produced Water Disposal
• Pre Carbon Bed
• Post Oil/Water Separator
• E-Coat Paint
• Compressor Condensate
• Pre R.O. Membrane Water
• Plating Bath
• Aerosol Mists

Materials of Construction:

• Absorbent: Proprietary polymer
• Support Construction: 100% polyolefin
• Seal Material: Polyethylene Foam

Recommended Vessels: Parker LTG10 and LTG20 polymeric vessels and equivalent competitive vessels.

Cartridge Code:

• TBC = TruBind Cartridge
• Cartridge Length Code: 10 (9-13/16 in / 249 mm), 20 (19-15/16 in / 506 mm)
• Outside Diameter Code: 4 (4-1/2 in / 114 mm)
• Seal Material: A = Polyolefin Foam Gasket (standard for "DO" seal design)
• Support Core: A = Standard Wall Polypropylene Core
• End Cap Configuration: DO = Double-Open-End (gasket seal)

Operating limits

Maximum Recommended Operating Conditions:

• Temperature:
  • 150°F (65°C) @20 psid (1.4 bar)
  • 180°F (82°C) @10 psid (0.7 bar)
• Pressure: 40 psid (2.8 bar) @ 75°F (24°C)
• Changeout Pressure Drop (net): 10 psi (0.7 bar)
• pH Range: 2 - 12

Feed water

TruBind cartridges effectively reduce trace hydrocarbon contamination in aqueous fluids, including free, emulsified, and dissolved oils, synthetic lubricants, grease, and a multitude of organic solvents.

Product water

Hydrocarbon Removal Efficiency:

• Typically reduces trace hydrocarbon contaminant in excess of 95% in single pass mode.
• This efficiency is based on an equivalent flow rate of 3.0 gpm per 10-inch cartridge.
• Efficiency can be maintained only to a net differential pressure of 10 psi.
• Series or multipass filtration can virtually eliminate hydrocarbon contamination.
• TCLP testing indicated effluent hydrocarbon levels in water to be below current and proposed EPA limits.

Hydrocarbon Absorbent Capacity:

• The TruBind cartridge medium has the potential to remove up to 500 grams (approximately one pint) of low density hydrocarbon contaminant.
• Absorbent capacity will decrease as density of hydrocarbon increases.

Mechanical / hydraulic

Cartridge Dimensions (nominal):

• Lengths: 9-13/16 in (249mm), 19-15/16 in (506mm)
• Outside Diameter: 4-1/2 in (114 mm)
• Inside Diameter: 1-1/16 in (27 mm)

Flow Rate:

• A maximum flow rate of 3.0 gpm per 10-inch length cartridge is recommended for the most effective removal of trace hydrocarbon contaminant.

Flow Factor:

• 0.1 psid per 1 gpm at 1 cks viscosity per 10 in cartridge

BioSafety

The TruBind cartridge is classified as non-hazardous and incinerable. Disposal must be dictated by local regulations pertaining to the absorbed contaminant.

---

Disclaimer: This summary is based on the provided text extract and may not include all figures, footnotes, or the latest revisions found in the official PDF datasheet. For contractual data, always refer to the specific OEM PDF revision used on the project.

Official datasheet (PDF)

Lenntech datasheet mirror