
Tóm tắt tài liệu kỹ thuật
G Wound
Engineering summary from PDF text extraction for G Wound. Verify every value with the OEM datasheet.
Summary
Product identification
G-Series Wound Depth Filter cartridges are available in a variety of lengths and micron ratings.
- Available lengths: 9.75 to 50 inches
- Micron ratings: 0.5 to 400 µ
- Filtration media: FDA polypropylene, bleached cotton, FDA bleached cotton, natural cotton, polyester, nylon, and glass
- Core materials: Polypropylene, 304 & 316 stainless steel, tin, and glass
- Performance-enhancing end-configurations are available to fit various process requirements.
Construction Materials
- Filtration Media:
- FDA Polypropylene
- Bleached Cotton
- FDA Bleached Cotton
- Natural Cotton
- Polyester
- Nylon
- Glass
- End Caps: Polypropylene
- Core:
- Polypropylene
- 304 Stainless Steel
- 316 Stainless Steel
- Tin
- Glass
- O-Rings/Gaskets:
- Buna
- EPDM
- Silicone
- Teflon®
- Viton®
Dimensions (Nominal)
- Length: 9.75 to 50 inches (24.8 to 127 cm)
- Outside Diameter: 2.5 inches (6.4 cm) or 4.5 inches (11.4 cm)
- Inside Diameter: 1.06 inches (2.69 cm)
Operating limits
- Change Out ΔP (recommended): 35 PSID
- Temperature (max): Dependent on materials of construction
- Differential Pressure (max): 50 PSID (3.4 bar) at 68˚F (20˚C)
Typical Applications
- Chemicals
- Pharmaceutical
- Consumer Products
- Photographic
- Food and Beverage
- Plating Solutions
- Lubricating Oils
- Edible Oils
- Paints
- Water
- Inks
- Waste Treatment
- Petrochemicals
Ordering Information
The filter cartridges are ordered using a code structure: G [Media] [Rating (µ)] [Diameter] [Length] [Core] [End Cap Style] [O-Rings]
- Media:
- P = FDA Polypropylene
- C = Bleached Cotton
- CC = FDA Bleached Cotton
- CN = Natural Cotton
- PE = Polyester
- N = Nylon
- G = Glass
- Rating (µ): 0.5, 1, 3, 5, 10, 20, 25, 30, 50, 75, 100, 200, 250, 400
- Diameter:
- A = 2.5
- BB = 4.5
- Length:
- 9.75” (24.76cm)
- 9.875” (25.08 cm)
- 10” (25.4 cm)
- 19.5” (49.53 cm)
- 20” (50.8 cm)
- 29.25” (74.26 cm)
- 30” (76.2 cm)
- 39” (99.1 cm)
- 40” (101.6 cm)
- 50” (127 cm)
- Core:
- P = Polypro
- A = 304 SS
- S = 316 SS
- T = Tin
- FG = Glass
- End Cap Style:
- 2P = DOE Flat Polyfoam Gasket
- 3 = 222 w/Fin
- 4 = 222 w/Flat Cap
- 5 = 222 w/Spring
- 6 = 226 w/Flat Cap
- 7 = 226 w/Fin
- 8 = 226 w/Spring
- 9 = SOE w/ Spring
- 10 = DOE w/PP Core Extender
- 10K = DOE w/ Crimped Ext. Core
- 10X = DOE w/ SS Core Extender
- O-Rings:
- B = Buna
- E = EPDM
- S = Silicone
- T = Teflon®
- V = Viton®
Disclaimer: Filtration data presented is representative of performance observed in controlled laboratory testing. It is not given as a warranty, specification or statement of fitness for use. Specific performance can vary widely depending on contaminant type, fluid properties, flow rates and environmental conditions. It is recommended that users conduct thorough qualification testing to assure the product functions as required. This extraction may miss figures, footnotes, or revisions; contractual data must match the OEM PDF revision used on the project.
Official datasheet (PDF)
Nội dung tổng hợp từ tài liệu kỹ thuật công khai nhằm tra cứu và so sánh sơ bộ. Bản tóm tắt không thay thế bảng dữ liệu hiện hành được nhà sản xuất chứng nhận. Kiểm tra phiên bản và giới hạn thiết kế trước khi sử dụng.