Tóm tắt tài liệu kỹ thuật
RO XLERO XLE
Engineering summary from PDF text extraction for RO XLERO XLE. Verify every value with the OEM datasheet.
Summary
Product Identification
The MICRODYN RO XLE series consists of ultra-low energy reverse osmosis (RO) membrane elements designed for water purification applications where reduced energy consumption is critical. These elements feature low-energy membranes to upgrade existing RO systems and operate under ultra-low pressure conditions.
- Membrane Chemistry: Thin-Film Composite Polyamide
- Construction: Spiral-Wound Membrane Element with Fiberglass Outerwrap (or Tape outerwrap for some models)
Performance Specifications
The MICRODYN RO XLE elements offer high salt rejection rates and consistent permeate flow.
- Stabilized Salt Rejection: 99.2%
- Minimum Salt Rejection: 99.0%
Performance data is based on test conditions of 500 ppm NaCl, 6.9 bar (100 psi), 25°C (77°F), 15% recovery, pH 8.0, and 30 minutes operation. Actual flow rates will be no more than 15% below the values shown.
Model Specifics
- 4040-XLE
- Permeate Flow: 9.8 m³/day (2,600 GPD)
- Membrane Area: 7.9 m² (85 ft²)
- 8040-XLE-400
- Permeate Flow: 45.4 m³/day (12,000 GPD)
- Membrane Area: 37.2 m² (400 ft²)
- 8040-XLE-440
- Permeate Flow: 50.0 m³/day (13,200 GPD)
- Membrane Area: 40.9 m² (440 ft²)
Physical Dimensions
All models on this sheet feature diamond-shaped feed spacers.
- 4040-XLE
- Dim. A: 1,016 mm (40.0 inches)
- Dim. B: 99 mm (3.9 inches)
- Dim. C (Outer Diameter): 19.1 mm (0.75 inches)
- Permeate Tube: Male, with a protruding tube (Dim. D) of 26.7 mm (1.05 in)
- Outerwrap Type: Tape
- Element Weight: 4 kg (9 lb)
- 8040-XLE-400
- Dim. A: 1,016 mm (40.0 inches)
- Dim. B: 201 mm (7.9 inches)
- Dim. C (Inner Diameter): 28.6 mm (1.125 inches)
- Permeate Tube: Female
- Outerwrap Type: Fiberglass
- Element Weight: 16 kg (36 lb)
- 8040-XLE-440
- Dim. A: 1,016 mm (40.0 inches)
- Dim. B: 201 mm (7.9 inches)
- Dim. C (Inner Diameter): 28.6 mm (1.125 inches)
- Permeate Tube: Female
- Outerwrap Type: Fiberglass
- Element Weight: 17 kg (37 lb)
Operating Limits
- Maximum Operating Pressure:
- Tape Outerwrap Models: 21 bar (300 psi)
- Fiberglass Outerwrap Models: 41 bar (600 psi)
- Maximum Operating Temperature: 45°C (113°F)
- Cleaning pH Range: 1.0 – 12.0 (Refer to the Membrane Cleaning Guide for temperature and pH limits)
- Chlorine Tolerance: < 0.1 ppm (Pretreatment is recommended for free chlorine and other oxidizing agents)
- Maximum Pressure Drop:
- 1 bar (15 psi) per element
- 4 bar (60 psi) per housing
- Maximum SDI₁₅: 5.0
- Maximum Turbidity: 1 NTU
Important Information
- Start-up: MANN+HUMMEL Water & Fluid Solutions recommends flushing elements for 30 minutes at low pressure and discarding permeate during the flush. Consult the Element Start-Up Guide – System Start-Up (TSG-O-005) for detailed procedures.
- Cleaning: MICRODYN RO membrane elements require periodic cleaning. Refer to the Membrane Cleaning Guide – Water Application Elements (TSG-C-001) for instructions.
- Storage: Proper storage of MICRODYN RO membrane elements is essential. See Element Storage Guides (TSG-O-009 & TSG-O-010).
Disclaimer: This summary is based on extracted text and may not include all figures, footnotes, or the latest revisions. Contractual data must match the OEM PDF revision used on the project.
Official datasheet (PDF)
Nội dung tổng hợp từ tài liệu kỹ thuật công khai nhằm tra cứu và so sánh sơ bộ. Bản tóm tắt không thay thế bảng dữ liệu hiện hành được nhà sản xuất chứng nhận. Kiểm tra phiên bản và giới hạn thiết kế trước khi sử dụng.