Tóm tắt tài liệu kỹ thuật
TW30-2514
Engineering summary from PDF text extraction for TW30-2514. Verify every value with the OEM datasheet.
Summary
Product Identification
FilmTec™ Reverse Osmosis (RO) Elements are designed for small commercial systems purifying less than one gallon per minute (0.2 m³/d) of RO water. These elements are available in various sizes to meet space requirements and aim to provide high-quality water, long-lasting performance, and reliability. FilmTec™ XLE extra low energy elements operate at lower pressures to reduce energy costs.
The specific product identified is the FilmTec™ TW30-2514 membrane element.
Operating Limits
- Membrane Type: Polyamide Thin-Film Composite
- Maximum Operating Temperature: 113°F (45°C)
- Maximum temperature for continuous operation above pH 10 is 95°F (35°C).
- Maximum Operating Pressure: 600 psig (41 bar)
- Maximum Pressure Drop (per element): 13 psig (0.9 bar)
- Maximum Pressure Drop (across entire pressure vessel): 30 psi (2.1 bar)
- pH Range - Continuous Operation: 2 - 11
- pH Range - Short-Term Cleaning (30 min.): 1 - 13
- Maximum Feed Silt Density Index (SDI): 5
- Free Chlorine Tolerance: <0.1 ppm (Under certain conditions, free chlorine and other oxidizing agents can cause premature membrane failure, which is not covered under warranty.)
Feed Water
The TW30-2514 element is tested with a 2,000 ppm NaCl feed stream.
Product Water
For the TW30-2514 element:
- Applied Pressure: 225 psig (15.5 bar)
- Permeate Flow Rate: 200 gpd (0.76 m³/d)
- Stabilized Salt Rejection: 99.5%
These values are based on test conditions: 2,000 ppm NaCl feed stream, 77°F (25°C), and 5% recovery. Permeate flows for individual elements may vary +/-20%. Permeate obtained from the first hour of operation should be discarded.
The use of this product does not necessarily guarantee the removal of cysts and pathogens; effective reduction depends on the complete system design, operation, and maintenance.
Mechanical / Hydraulic
(1 inch = 25.4 mm)
TW30-2514 Element Dimensions:
- Maximum Feed Flow Rate: 6 gpm (1.4 m³/h)
- Dimension A: 14.0 inches (356 mm)
- Dimension B: 1.19 inches (30 mm)
- Dimension C: 0.75 inches (19 mm)
- Dimension D: 2.4 inches (61 mm)
TW30-2514 elements fit nominal 2.5 inch I.D. pressure vessels.
General Information and Guidelines
- Keep elements moist at all times after initial wetting.
- Adherence to operating limits and guidelines is essential to maintain warranty.
- During prolonged system shutdowns, immerse membrane elements in a preservative solution to prevent biological growth.
- Customers are responsible for the effects of incompatible chemicals and lubricants on elements.
- Avoid any abrupt pressure or cross-flow variations during start-up, shutdown, cleaning, or other sequences to prevent membrane damage.
- During start-up, gradually increase feed pressure over 30-60 seconds and achieve the set operating cross-flow velocity gradually over 15-20 seconds.
- Avoid static permeate-side backpressure at all times.
Disclaimer
This extraction may miss figures, footnotes, or revisions present in the original PDF. For contractual data, please refer to the specific OEM PDF revision used on your project.
Official datasheet (PDF)
Nội dung tổng hợp từ tài liệu kỹ thuật công khai nhằm tra cứu và so sánh sơ bộ. Bản tóm tắt không thay thế bảng dữ liệu hiện hành được nhà sản xuất chứng nhận. Kiểm tra phiên bản và giới hạn thiết kế trước khi sử dụng.