Tóm tắt tài liệu kỹ thuật
CSM RE8040-BLF440
Engineering summary from PDF text extraction for CSM RE8040-BLF440. Verify every value with the OEM datasheet.
Summary
Product identification
The RE8040-BLF440 is an ultra-low pressure grade reverse osmosis (RO) element designed for low total dissolved solids (TDS) water. It is suitable for Industrial and Municipal applications. This product is certified to NSF/ANSI/CAN 61.
General Features
- Ultra-Low-Energy Consumption
- Extended effective membrane area
- Membrane Type: Thin-Film Composite
- Membrane Material: Polyamide (PA)
- Element Configuration: Spiral-Wound, FRP Wrapping
Performance Specifications
Test Conditions:
- NaCl solution: 500 mg/L
- Applied pressure: 100 psig (0.69 MPa)
- Recovery: 15%
- Temperature: 77℉ (25℃)
- pH: 6.5–7.0
- Permeate flow rate for each element may vary +25% / -15%.
Performance:
- Permeate Flow Rate: 12,650 GPD (47.9 m³/day)
- Nominal Salt Rejection: 99.2% (Minimum 99.0%)
- Effective Membrane Area: 440 ft² (40.9 m²)
Mechanical / Hydraulic
- Model Name: RE8040-BLF440
- Dimensions:
- A: 40.0 inch (1,016 mm)
- B: 7.9 inch (200 mm)
- C: 1.12 inch (28.5 mm)
- Weight: 15kg
- Part Numbers:
- Inter-Connector: SWA01049
- Brine Seal: SWA01043
- Each membrane element is supplied with one interconnector (coupler) and four O-rings.
- All RE8040 elements fit nominal 8.0 inch (203.2 mm) I.D. pressure vessels.
- The element shell is FRP (Fiber Reinforced Plastic).
Operating limits
- Max. Pressure Drop / Element: 15 psi (0.10 MPa)
- Max. Pressure Drop / 240” Vessel: 60 psi (0.41 MPa)
- Max. Operating Pressure: 600 psi (4.14 MPa)
- Max. Feed Flow Rate: 75 gpm (17.0 m³/hr)
- Min. Concentrate Flow Rate: 16 gpm (3.6 m³/hr)
- Max. Operating Temperature: 113°F (45°C)
- Operating pH Range: 2.0 – 11.0
- CIP pH Range: 1.0 – 13.0
- Max. Turbidity: 1.0 NTU
- Max. SDI (15 min): 5.0
- Max. Chlorine Concentration: < 0.1 mg/L
General Handling Procedures
- Elements in boxes must be kept dry at room temperature (7–32°C; 40–95°F) and not stored in direct sunlight.
- For wet-type elements, a preservative solution (1% sodium metabisulfite solution) is added to prohibit microbial growth.
- Permeate from the first hour of operation should be discarded.
- Stabilized salt rejection is generally achieved within 1–48 hours of continuous use.
- Keep elements moist at all times after initial wetting.
- Avoid excessive pressure and flow spikes.
- Only use chemicals compatible with the membrane elements and components. Use of incompatible chemicals may void the element's limited warranty.
- Permeate pressure must always be equal to or less than the feed/concentrate pressure. Damage caused by permeate back pressure voids the element's limited warranty.
- The element shell is FRP. Be aware of glass fiber strands and use safety equipment.
Disclaimer: This summary is based on extracted text and may not include all figures, footnotes, or the latest revisions. Contractual data must match the OEM PDF revision used on the project.
Official datasheet (PDF)
Nội dung tổng hợp từ tài liệu kỹ thuật công khai nhằm tra cứu và so sánh sơ bộ. Bản tóm tắt không thay thế bảng dữ liệu hiện hành được nhà sản xuất chứng nhận. Kiểm tra phiên bản và giới hạn thiết kế trước khi sử dụng.