Tóm tắt tài liệu kỹ thuật
LEWATIT® S 2568
PDF datasheet mirror for LEWATIT® S 2568 (Lanxess LEWATIT). Verify with OEM before design.
Summary
Product Identification
- Product Name: LEWATIT® S 2568
- Product Type: Strongly acidic cation exchange resin
- Matrix: Styrene-divinylbenzene copolymer
- Structure: Macroporous, monodisperse
- Functional Group: Sulfonic acid
- Common Description: Na⁺
- Appearance: Beige-gray, opaque
- Delivery Form: Na⁺
Applications
LEWATIT® S 2568 is especially applicable for:
- Decationization of solutions of organic products (e.g., sugar beet, sugar cane, starch sugar, glycerine, gelatine, food acids).
- Extraction of amino acids (e.g., lysine).
- Softening of solutions, especially of sugar thin juices.
The resin offers features such as:
- High exchange flow rates during regeneration and loading.
- Good utilization of capacity.
- Low rinse water demand.
- Homogeneous throughput of regenerants, water, and solutions.
- Nearly linear pressure drop gradient allowing for higher bed depth.
- Good separation behavior in mixed bed applications.
Specified Data
- Uniformity coefficient: max. 1.1
- Mean bead size (d50): 0.60-0.70 mm
- Total capacity (delivery form): min. 1.7 eq/L
Typical Physical and Chemical Properties
- Bulk density for shipment (+/- 5%): 740 g/L
- Density (approx.): 1.2 g/mL
- Water retention (delivery form): approx. 50-55 wt. %
- Volume change (Na⁺ - H⁺): max. approx. 10 %
- Stability pH range: 0-14
- Stability temperature range: 1-120 °C
- Storage time (after delivery): max. 2 years
- Storage temperature range: -20 - +40 °C
Operating Parameters
- Operating temperature (max.): 120 °C
- Operating pH range during exhaustion: 0-14
- Bed depth for single column (min.): 800 mm
- Backwash bed expansion (per m/h at 20°C): 4 %
- Specific pressure loss (at 15°C): 0.8 kPa*h/m²
- Max. pressure loss during operation: 300 kPa
- Specific flow rate (max.): 5 BV/h
- Freeboard during backwash (min. vol. %): 80-100 %
Regeneration Parameters
HCl Regeneration:
- Concentration: approx. 4-6 wt. %
- Quantity co-current (min.): 100 g/L resin
- Quantity counter-current (min.): 55-65 g/L resin
H₂SO₄ Regeneration:
- Concentration: approx. 1.5-3 wt. %
- Quantity co-current (min.): 150 g/L resin
- Quantity counter-current (min.): 100 g/L resin
NaCl Regeneration:
- Concentration: approx. 8-10 wt. %
- Quantity co-current (min.): 200 g/L resin
- Quantity counter-current (min.): 100 g/L resin
General Regeneration:
- Regeneration contact time (min.): 20 minutes
- Slow rinse at regeneration flow rate (min.): 2 BV
- Fast rinse at service flow rate (min.): 4 BV
Additional Information & Regulations
- Safety precautions: Avoid contact with strong oxidants. Observe safety data sheet.
- Disposal: According to European waste nomenclature.
- Storage: Recommended above freezing point, dry, under roof, out of direct sunlight. If frozen, thaw gradually at ambient temperature.
- Packaging stability: Limited to 24 months under recommended storage conditions.
Disclaimer: This extraction may miss figures, footnotes, or revisions. Contractual data must match the OEM PDF revision used on the project.
Official datasheet (PDF)
Nội dung tổng hợp từ tài liệu kỹ thuật công khai nhằm tra cứu và so sánh sơ bộ. Bản tóm tắt không thay thế bảng dữ liệu hiện hành được nhà sản xuất chứng nhận. Kiểm tra phiên bản và giới hạn thiết kế trước khi sử dụng.