Tóm tắt tài liệu kỹ thuật
SP Series 4 x 28
Engineering summary from PDF text extraction for SP Series 4 x 28. Verify every value with the OEM datasheet.
Summary
Product identification
- 3M™ Liqui-Cel™ SP-4x28 Series Membrane Contactor
- Applications:
- Fluoroelastomer: General Purpose
- Perfluoroelastomer: Ultra Pure Water
Membrane Characteristics
- Cartridge Configuration: Extra-Flow with Center Baffle
- Membrane/Potting Material: Polyolefin / Polyethylene
Operating limits
- Liquid Flow Guidelines: 1.1-6.8 m³/hr (5-30 gpm)
- Liquid must flow on the shellside
- Maximum Shellside LIQUID Working Temperature/Pressure:
- 5-25°C, 4.1 barg (41-77°F, 60 psig)
- 50°C, 1.0 barg (122°F, 15 psig)
- If no vacuum is used, 1 barg (15 psig) can be added to pressures above.
- Maximum Applied Gas Pressure: 4.1 barg at 25°C (60 psig at 77°F)
- Note: Liquid pressure should always exceed gas pressure.
- See the official PDF for complete temperature/pressure limits for housings and membrane.
Mechanical / hydraulic
- All dimensions are nominal values for the Polypropylene housing with NPT connections. See full housing drawing on 3M.com/Liqui-Cel for additional details.
- Dimensions (nominal):
- 116 mm (4.6 in)
- 85 mm (3.3 in)
- Priming Volume (approximate):
Housing Material Shellside Lumenside Polypropylene 2.9 L (0.8 gal) 0.9 L (0.2 gal) 316L SS 2.9 L (0.8 gal) 0.7 L (0.2 gal) - Housing Characteristics:
- Material: Polypropylene, 316L SS (32 Ra finish)
- Flange Connections:
- Shellside (Wetted surface):
- 1 inch Sanitary
- ¾ inch NPT Female
- 1 inch George Fisher
- Rc ¾ per JIS B0203
- Lumenside (Gas/Vacuum):
- 1 inch 90° Sanitary
- ¾ inch 90° NPT Female
- Rc ¾ per JIS B0203
- 1 inch Sanitary
- Shellside (Wetted surface):
- Seal Material Options: Fluoroelastomer, Perfluoroelastomer
- Weight (approximate):
Housing Material Dry Water-filled Polypropylene 4 kg (9 lbs) 7 kg (16 lbs) 316L SS 7 kg (16 lbs) 10 kg (22 lbs)
Regulatory
- Complies with the limits as set by RoHS Directive 2011/65/EU Annex II; recasting 2002/95/EC.
- Constructed of FDA CFR title 21 compliant materials for wetted parts only at ambient temperatures.
Disclaimer: This summary is based on extracted text and may not include all figures, footnotes, or the latest revisions from the original PDF datasheet. For contractual data, always refer to the specific OEM PDF revision used on your project.
Official datasheet (PDF)
Nội dung tổng hợp từ tài liệu kỹ thuật công khai nhằm tra cứu và so sánh sơ bộ. Bản tóm tắt không thay thế bảng dữ liệu hiện hành được nhà sản xuất chứng nhận. Kiểm tra phiên bản và giới hạn thiết kế trước khi sử dụng.