High Flow

Summary

Product Identification

The product is a Nominal High Flow Z filter, a polypropylene melt-blown depth media filter featuring Z.Plex* technology for increased flow filtration. A single 40-inch High Flow Z filter is stated to have the dirt holding capacity of 50 standard 40-inch length depth cartridge filters.

Features and Benefits

• Large diameter for high volume filtration
• Polypropylene melt-blown depth media filter design
  • Graded density retains particles throughout the full diameter of the filter
  • Enhanced dirt-holding capacity yields quicker upset recovery and less surface binding
  • Outperforms pleated filters
• Easier and less frequent change-outs than conventional standard 2.5 in. outer diameter depth filters
• Lower total cost of filtration operations
• Superior SDI reduction

Applications

• Amine filtration
• Well injection
• Produced water filtration
• Waterflood
• Enhanced oil recovery

Mechanical / Hydraulic

Specifications

• Nominal Micron Ratings: 1, 5 microns
• Lengths:
  • 40 in (101.6 cm)
  • 60 in (152.4 cm)
• Inner Diameter:
  • 40 in length: 1.6 in (4.1 cm)
  • 60 in length: 3.1 in (7.9 cm)
• Outer Diameter: 6.5 in (16.5 cm)
• Materials of Construction:
  • Filter Media: Polypropylene
  • Adapters: Polypropylene
  • Elastomer: EPDM

Operating Limits

Performance Conditions

• Maximum pressure drop:
  • 50 psid (3.4 bar) @ 77°F (25°C)
  • 35 psid (2.4 bar) @ 160°F (71°C)
• Recommended change-out pressure drop: 35 psid (2.4 bar) @ 77°F (25°C)

Performance Data

Efficiency Information

The removal efficiency of nominal filters, as opposed to absolute-rated filters (which reject at least 99% of particles of the listed micron size), is dependent on particle shape, size, composition, application, and testing protocol. Nominal-rated filters have a wider distribution of pore sizes and a wider distribution of rejected particle sizes. Efficiency of nominal filters varies by application.

Clean Water Flow Rate

Clean water flow rate data based on 40 in and 60 in length filters is presented in graphs within the official PDF. See the official PDF for exact tabulated values and graphical representation.

Quality and Compliance

• Manufactured under a quality management system certified to meet ISO 9001 standards.
• Each filter is assigned a lot code for traceability.
• Compliance:
  • US FDA 21 CFR compliant materials
  • Article 3 of the EU framework Regulation No. 1935/2004/EC Safety requirements
  • EU Plastics Regulation No. 10/2011 (may be used as intended in all compliant EU member states).
  • Meets USP Class VI-121 C plastics criteria.
  • NSF 61 certified
  • ACS certified (Attestation de Conformité Sanitaire) for EPDM o-rings only.
  • ISO 9001:2015 certified processes

Filter cartridges are designed and manufactured for resistance to a wide range of chemical solutions; users should carefully verify chemical compatibility as conditions vary with each application.

Ordering Information

Part Numbers

Part numbers are available for 40" and 60" lengths, and 1 or 5 micron nominal ratings.

• 40" length:
  • 1 micron: Part number 3146356 (HF.ZS 01-40-FSE)
  • 5 micron: Part number 3146358 (HF.ZS 05-40-FSE)
• 60" length:
  • 1 micron: Part number 3156436 (HF.ZS 01-60-TSE)
  • 5 micron: Part number 3156621 (HF.ZS 05-60-TSE)

Description Key

• End #1 Adapter:
  • F = 226 O-Ring
  • T = 338 O-Ring
• End #2 Adapter: S = Closed end with ergonomic handle
• Elastomer Material: E = EPDM

Elastomer Kits

Elastomer kits are available for different adapter types and materials:

• 40" (226) Adapter:
  • Buna: Part number 3195517 (803 quantity)
  • Silicone: Part number 3195811 (803 quantity)
  • Viton²: Part number 3195812 (803 quantity)
  • Note: Two (2) are required on 226 adapters for each filter.
• 60" (338) Adapter:
  • Buna: Part number 3195815 (25 quantity)
  • Silicone: Part number 3195814 (25 quantity)
  • Viton²: Part number 3195816 (25 quantity) ² Viton is a registered mark of The Chemours Company.

---

Disclaimer: This summary is based on the provided text extract and may not include all figures, footnotes, or the latest revisions. For contractual data, always refer to the official OEM PDF revision used on your project.

Official datasheet (PDF)

Lenntech datasheet mirror